4C Error In Samsung Washing Machine: How To Fix 4C Or 4E Error Code Step by Step?
If the 4C error in Samsung washing machine is displayed on the screen when you start using the washer.
It means that the washing machine has detected a problem with the water supply.
In this article, I will discuss the most common reason why the washer displays error code 4E or 4C. And how to fix it by following the below-mentioned simple steps.
You can also watch the video.
In brief, about Samsung 4c error code
Samsung washing machines are well-known for their high efficiency and innovative features.
However, just like any other equipment, they can malfunction from time to time.
As I already mentioned above, the washer screen displays 4E or 4C whenever there is a problem with the water supply.
This might be caused due to a block, or the Samsung machine is experiencing either low water pressure or a reduced flow rate in the mains water supply.
Make sure the water pressure is from 0.5 bar to 8 bar.
You might see the fault code during rinsing or at the very initial stage.
What are the causes of error code 4C?
Here is the list due to which the Samsung washing machine may display the error code 4C:
- No water is coming from the main water supply to the washer.
- The water hose mesh filter might be blocked.
- The water hose may be leaking.
- There may be a blockage in the dispenser drawer.
- The water pressure is not enough and does not meet the minimum required pressure requirement.
Follow these troubleshooting steps to resolve the 4C error and restore your Samsung washing machine to full functionality:
Note: Before starting the troubleshooting process, turn off and unplug your washing machine from the power source.
1. Water inlet valve
Let’s start the troubleshooting process by first checking the inlet valve.
Now open the cold water tap fully.
The cold water tap should deliver water with a pressure of 0.5 bar to 8 bar.
The water supply valve’s debris filter can also become clogged with dirt.
If you are not getting water with enough pressure, the water tap/inlet valve needs to be cleaned or replaced.
2. Check the water hose for leaks or blockage.
It’s possible that the water hose could get blocked, kinked, or bent, which is connected to the washer.
Also, make sure the hose is not damaged.
This can be done by visual inspection for leaks by keeping the water tap fully open.
In case you find the water hose blocked, kinked, or bent, time to replace it with a new one.
If you did not find any problem till here, then move on to the next step.
3. Check & Clean the water hose mesh filter
First, make sure to turn off the water supply tap fully.
Now, carefully remove the hose that connects to the water supply to the washer.
Next, detach the L-shaped arm from the washing machine.
Slowly pull out the mesh filters from the washer.
Please give them a gentle rinse under flowing water until they are nice and clean.
If you wish, use some liquid detergent to clean it.
After cleaning, carefully put the mesh filters back from where it was removed.
Now you can reconnect the hose to the washing machine and open the cold water supply tap fully.
Finally, check for leaks once you open the water supply, and you’re good to go!
4. Check & Clean the detergent/dispenser drawer of the Samsung washer.
Sometimes the detergent drawer could get blocked. And because of the blockage, the washer displays the error code 4c.
To solve this, you just need to clean the detergent drawer.
First, remove it and rinse it with water nicely.
You can use mild liquid detergent while cleaning it.
Now put it back to its original position.
And now Your detergent/dispenser drawer is clean and ready.
Conclusion
When your Samsung washing machine displays the 4C error code, it means there is a problem with the water supply to the washer.
The error code 4c is caused by the following problems:
- Blocked water hose mesh filter.
- Leaking water hose.
- A blockage in the dispenser drawer.
- Insufficient water pressure form of tap water.
To resolve the issue, you can troubleshoot by checking and cleaning the water inlet valve, inspecting the water hose for leaks or blockages, cleaning the water hose mesh filter, and cleaning the detergent/dispenser drawer.
By following the above given all simple steps, you can restore your Samsung washing machine to full functionality and resolve the 4C error.
Frequently asked questions (FAQ)
How do I reset my Samsung washer?
Just turn off the washer and unplug the washer cable from the power socket.
Wait for a couple of minutes before plugging it back in.
Turn on the washing machine and check if still the 4C error code is displayed.
When to call a professional for repair?
If you have followed the above-mentioned troubleshooting steps correctly, and still the 4C Error in Samsung washing machine is displayed.
It means that may be some internal problem, and it’s time to contact a professional for repair.
For more different gadgets reviews please visit: 0gadget
