We need clean and safe water for our daily activities, whether it’s for drinking, cooking or washing our clothes.
clean a mesh filter of water supply hose on a regular basis is also necessary to continuously get clean water.
The mesh filter may accumulate dirt, silt, and mineral deposits over time, which can reduce the water flow as well as potentially damage the appliances.
So in this article, I will provide you with a step-by-step guide on how to clean the mesh filter on a water supply hose.
This will ensure that your washing machine always has clean water to use.
If you wish, you can watch this video also.
Step 1: Preparation
Before you start the cleaning process, you will need a few tools and materials, which are listed below.
- Adjustable pliers
- A bucket or basin
- Distilled white vinegar
- A soft brush or toothbrush
- Clean cloth or paper towels
Step 2: Turn Off the Water Supply
Now you turn off the water supply tap which supplies the water to the washing machine, by rotating it clockwise until it is fully closed.
Step 3: Disconnect the Water Supply Hose
At the back side of the washing machine, you will find an L-shaped arm fitting to which the Water Supply Hose is connected.
You have to disconnect this L-shaped arm fitting from the water supply hose.
Once it’s disconnected, cover the hose connection with a towel to prevent water from leaking due to air pressure in the water supply hose.
Step 4: Pulling out the mesh filter
Here you will need the plier tool.
With the help of a plier, gently pull out the mesh filter, as shown in the image.
Step 5: Clean a mesh filter of water supply hose
Place the removed mesh filter in a wash basin or bucket filled with water.
Add some detergent to the wash basin or bucket filled with water.
Now insert the removed mesh filter in the water, and allow it to soak for about 15-20 minutes.
After 15 minutes, please take out the mesh filter, and rub it with a brush gently without damaging the mesh.
Once you have nicely cleaned the mesh filter, rinse it under running water so any remaining debris is washed away.
Step 6: Inspecting the Mesh Filter
After the cleaning process is completed, inspect the mesh filter for any leftover debris or dirt.
If anything is left, repeat the cleaning process once again, or else the mesh filter is ready to install back into the washing machine.
Step 7: Reinstalling the Mesh Filter
Fix the mesh filter back to its original position from where it was removed with the help of pliers.
Step 8: Reattach the Hose
Using the adjustable pliers, loosen the nut that connects the water supply hose to the appliance.
Once loosened, carefully disconnect the hose from the appliance, taking care not to damage the hose or surrounding components.
Step 9: Turn On the Water Supply
Once everything is securely connected, open the shut-off valve to restore the water supply.
Slowly turn the valve counterclockwise to allow water to flow gradually, avoiding any sudden pressure changes.
Step 10: Check for Leaks and Test the Water Flow
This is the final step; inspect the connections for leaks.
If you notice any leaks, tighten them up even more or consider replacing the hose or washers.
Finally, please turn on the appliance and inspect the water flow to ensure it is even and free of obstructions.
FREQUENTLY ASKED QUESTIONS (FAQ)
What is a mesh filter on a water supply hose?
A mesh filter is a small screen or sieve-like component which is located at the end of a water supply hose.
As its name suggests (mesh filter), it’s used to filter water by stopping the debris, sediment, or particles from entering the water supply hose into the washing machine.
How frequently should I clean the mesh filter?
It’s essential to clean the mesh filter on a regulars basis, but the frequency of cleaning the mesh filter depends on various factors such as:
- The quality of your water supply
- The amount of debris it carries.
- How many clothes are washed daily
As a general guideline or rule of thumb, it is recommended to clean the filter every three to six months.
Whenever you notice a significant decrease in water flow or if you see 4C Error In Samsung Washing Machine, it is advisable to inspect and clean the mesh filter.
What tools do I need to clean the mesh filter?
Cleaning the mesh filter on a water supply hose requires only a few tools.
You may need a pair of pliers or an adjustable wrench to disconnect the hose from the water source.
A small brush or toothbrush can be handy for scrubbing away any stubborn debris on the filter.
One of the important to regularly clean the mesh filter on the water supply hose to maintain a continuous supply of clean water to the washing machine.
By following our step-by-step guide, you can do the process of cleaning the mesh filter quickly.
Feel free to give your feedback in the comments section below. Thanks for reading till the end of the blog.